New Black Antique Vintage Replica 34 24 Springer Fork Front End

  

NEW BLACK ANTIQUE VINTAGE REPLICA 34" 24" SPRINGER FORK FRONT END. Brake Calipers & Brake Pads. Turn Signals & Tail Lights. Gas Tanks & Caps Related. Swingarms & Wide Drive Kits.

Front Ends DNA Wide Glide 41mm. Front End Fork Tubes 39 & 41mm.

Front End Sliders & Lower Legs. Triple Trees / Fork Related. Wheel Bearings Axles & Spacers. Wheels 40 Spoke Billet Hub.

Wheels 60 Spoke Billet Hub. Wheels 80 Spoke Billet Hub. Wheels 80 Spoke Kc Int. Wheels Custom Mag Wheel Sets.

Wheels DNA Fatty 40 Fat Spoke. Wheels Ultima 48 Fat spoke. Wheels Dna Mammoth 52 Fat Spoke. Please check availability on all front ends, some lengths might be on backorder!!

You will receive a free springer axle kit. Springer shown above may be stock and you will receive size listed in ad.

Fits most Big Twin 1949-present bobbers and choppers with 1" neck bearings (except FXR, Dyna Glide and Touring models)we have in stock head cups that will work on 1954 up XL Sportsters to convert neck to 1" bearings and head cups. Features upper and lower brass zerk fittings to keep your front end well greased for years of service. Kit includes chrome main springs, neck top nut, top springer riser bracket and rocker bolts. Springer has black fork legs and rocker assemblies. Requires the use of risers with 1/2-20 mounting bolts.

Inside rockers where axle mounts is approximately 8 3/4-9. Inside rocker bolts where rockers mount to lower fork is approximately 7 1/8-7 1/4. Riser bolt holes are 4 3/4 apart. Springer brake mount is on right side and has a 5/8 diameter hole.

You can use a springer disc front brake caliper right side mount when sitting on bike that is shown in our web store. You can also mount this springer on a 1952-81 XL Sportster if you use our optional head cup conversion kit. We have available (optional) 2", 4" and 6 billet chrome risers for springers. A 3/4 front axle kit which includes: axle, (2) chrome acorn style end nuts, wheel spacers that can be cut to required length, & various washers/shims. (Please note wheel spacers may not be the correct size for your bike or project).

If needed, head cups and bearings are available in our web store. Most springers do not use internal fork stops.

We also offer this springer front end in chrome. We have many sizes available: 4" under, 2" under, stock, +2.

Please check availability before purchasing as some sizes may be on backorder. Approximate distance from the bottom of your frame neck bearing to center line of axle on this springer is 25.

Length of this springer is considered 24 which is measured from the center of axle to bottom of lower tree. Overall from the top of springer to the axle is 34 approx. You could consider this a stock FXST Softail stock length springer. It works best on stock Softail or rigid frames. You can use a 21" or 16" wheel.

Length on orginal Harley EL FL FLH Knucklehead Panhead Shovelhead models was even lower than this unit measuring 18"/28" so this would be considered stock Knucklehead for example. Please make sure you check and make sure this size will fit your custom application. Below are photos of many other items related to the item listed above. THANK YOU FROM KCINTERNATIONAL - KCINT!

WARNING Limitation of Liability: KC International Motorcycle Supply (KCInt) shall not be held liable for any damages that result from the Improper installation of parts, use, control, alteration or maintenance of motorcycles. Improper installation can cause serious injury, death and/or property damage. We recommend that all parts are installed by a licensed motorcycle dealer which is certified to work on Harley Davidson® motorcycles. This dealer must use good judgment in helping customers in the selection of parts for installation. KC International Motorcycle Supply (KCInt) has no control over the judgment of others and assumes no responsibility or liability of any nature for the failure of others to use good judgment.

This also includes wrongful or negligent on behalf of you or any person acting on your behalf. Image Permission: Images used in our ads are the property of KC International Motorcycle Supply (KCInt) and have embedded watermarks not visable to the eye. KC International Motorcycle Supply (KCInt) has the right to change, edit or terminate the terms and conditions at any time without prior notice. All sales from KC International Motorcycle Supply (KCInt) constitutes an understanding and agreement to all policies, terms, and conditions set forth by KC International Motorcycle Supply. If there is a issue with your order we will try to contact you as soon as possible.

Payments must be made in U. In some parts of the country it is illegal to receieve or use some of our products. It is up to the customer to determine the items that are illegal in your area. KC International Motorcycle Supply, Inc. The following terms are affiliated with KC International Motorcycle Supply: KCINTERNATIONAL, KCINT, KCInternational.

Founded in 1978, KCInt built its reputation by providing high-quality after market motorcycle parts to its customers with courteous service. We provide quality products at competitive prices to our customers.

We have many hard to find parts for those early motorcycles and the newest creations for your latest custom motorcycle project. Order any time, you never have to wait to place a large order. To save time, please have your card information ready when ordering. Item must be unused and in sale-able condition.

KC International Motorcycle Supply (KCInt) is not responsible for any charges for labor, repairs, materials, down-time or lost profits due to returning any merchandise. RETURN AUTHORIZATION Before returning any item, please notify us so that we can provide you with a.

And we will give you specific instructions on how to proceed with your return. To speed authorization, please provide us with the invoice number, order number, and order date when you call.